How to Make Easy Pants

from wikiHow – The How to Manual That You Can Edit
Do you ever feel like making a pair of pants out of that crazy fabric you like but are afraid to try? Here’s a pattern that’s easy to make and looks flattering on almost every figure.

Steps

1. Prepare your fabric.
   • Wash and dry your fabric as per the care instructions that are usually found on the bolt of fabric purchased at the store. This prevents the fabric from shrinking after you make your pants and wash them.
2. Measure yourself.
   • Measure from your waist to the bottom of your crotch.
   • Also measure from the middle your waist on the left side to the middle of your waist on the right side for both front and back.
     • Be sure to write down your measurements!
3. Lay out fabric
   • Match the selvage ends, the ends of the fabric finished by the machine as it wove it.
   • Be sure to smooth out any wrinkles.
4. Mark and cut the crotch line
   • Using a marking pencil (if desired), draw a “u” shape on the top middle of the fold of the fabric. The height of the “u” should be the length from your waist to the bottom of your crotch.
   • Cut carefully and slowly. It may be harder to cut on some fabrics than it is on others, so take your time as to reduce mistakes.
     • Use pins if your fabric is too slippery
   • Cut the fold after your have cut your crotch line out.
5. Sew the crotch line
   • Pin the two pieces of fabric together and sew 5/8″ along the edge of the “u.” If desired, sew over stitches to reinforce them.
6. Put them together
   • This is the part that gets tricky! Taking the left and right hand corner of the pants on both sides, bring them together and lay the pants down facing you.
7. Make them wearable
   • Cut off excess fabric on the sides, but be sure to leave enough room for them to tie in the front and the back. Do not cut the fabric yet if you want to make a fabric tie. Use your left-to-right waist measurements for a perfect fit.
8. Make a tie:
   • Ribbon tie – Sew a length of ribbon onto the end of the fabric. Be sure that you have two ribbons in the front and two in the back.
   • Fabric tie – simply use the extra fabric at the top as a tie, making an upside down “L” shape cut on the front and back of the pants.
9. Wear!
   • To put on the pants, take the ties in the back and tie them around to the front. Then, take the ties in the front and tie them around to the back.

Tips

• Sew with a piece of scrap fabric, or fabric you don’t care for as much first. That way, if you make a mistake, you won’t feel as bad about it, since it was only practice.
• Select fabric that is comfortable!
  • Knits, like tee-shirt material, make good relaxing pants
  • Sturdier fabric, like cotton, will make more formal straight hanging pants.
  • Heavy material, like twill and denim, are probably not the best choices, since these pants are made to be tied, not buttoned.
• If you get frustrated, take a break, and do something else. You can always come back with a fresh look on things, and finish your pants successfully.

Things You’ll Need

• About a yard and a half of fabric, depending on your size.
• Scissors
• Sewing machine
• Measuring tape
• (optional) ribbon or ties
• (optional) marking pencil

Related wikiHows

• How to Learn the Basics of Sewing
• How to Use a Sewing Machine and Adjust the Stitches
• How to Sew a Winter Coat
• How to Sew a Blanket
• How to Sew a Button

Article provided by wikiHow, a wiki how-to manual. Please edit this article and find author credits at the original wikiHow article on How to Make Easy Pants. All content on wikiHow can be shared under a Creative Commons license.

Visit Wolfgangs Vault

Where Live Music Lives

Wolfgang’s Vault is the home for the past, present and future of live music. This is the exclusive destination for The Bill Graham Archives, the King Biscuit Flower Hour and the Record Plant along with a dozen other archives that live here, and are relived here. Within the Concert Vault are thousands of carefully restored and archived concert recordings to stream for free, hundreds of which are available for download.

Along the walls, halls and inner vaults of Wolfgang’s Vault is the greatest collection of concert posters, rock photography, vintage t-shirts and retro t-shirts, rock gear and concert related memorabilia.

Whether you are interested in legendary performances of the past or the greatest emerging performers of today, Wolfgang’s Vault is where you’ll find them, and the stories behind the scenes. Find today’s concert tours listed on Mojam and weekly rock reviews and criticism in the reborn Crawdaddy!: The Magazine of Rock.
Posted in Entertainment ]]> http://sightmap.wordpress.com/2008/10/15/link-wolfgangs-vault/feed/ 0 DarkLight wolfgangs-vault-ticket http://sightmap.wordpress.com/2008/10/09/homenet/ http://sightmap.wordpress.com/2008/10/09/homenet/#comments Thu, 09 Oct 2008 17:09:51 +0000 DarkLight http://sightmap.wordpress.com/?p=528 ]]> LocalHost

- 192.168.16.1
- 192.168.16.100 (Gravija)

Gravija : HomeServer

- http://67.175.134.193/
- http://67.175.134.193/wordpress/
- http://67.175.134.193/xampp/
- http://67.175.134.193/dreampod/
-
-

Hosted Sites

- FreeHostia : WP DLS
-

2827 N. Broadway Chicago, Il 60657
Phone: 773.248.2445
http://renaldispizzachicago.com

Restaurant Hours:
• Mon – Thurs 11am – Midnight
• Fri – Sat 11am – 2 am
• Sunday – 12pm – Midnight

Delivery Hours:
• Monday – Thursday 11am – Midnight
• Fri – Sat – 11am – 2 am
• Sunday – Noon – midnight

renadis3@sbcglobal.net

Black Bean and Chick Pea Chili

Diced Tomatoes (1 32oz can)
Black Beans (2 16oz cans)
Chick Peas (1/2 16oz can)
Onion (1 yellow)
Garlic (1 clove)
Red, Black, Chipotle, Cheyenne and Chili Pepper (1/2 tsp each)
Pure Maple Syrup (1 tsp, Dark Amber)
Mustard (1 tsp, dill)
Lemon Juice (1 tsp)
Pure Honey (1 tsp)
Paprika (1/2 tsp)
Salt (1 tsp)

Windows Logo+D (Display the desktop)
Windows Logo+M (Minimize all of the windows )
Windows Logo+SHIFT+M (Restore the minimized windows )
Windows Logo+E (Open My Computer)
Windows Logo+F (Search for a file or a folder)
CTRL+Windows Logo+F (Search for computers)
Windows Logo+F1 (Display Windows Help)
Windows Logo+ L (Lock the keyboard)

CTRL+C (Copy)
CTRL+X (Cut)
CTRL+V (Paste)
CTRL+Z (Undo)
DELETE (Delete)
SHIFT+DELETE (Delete the selected item permanently without placing the item in the Recycle Bin)
CTRL while dragging an item (Copy the selected item)
CTRL+SHIFT while dragging an item (Create a shortcut to the selected item)
F2 key (Rename the selected item)
CTRL+RIGHT ARROW (Move the insertion point to the beginning of the next word)
CTRL+LEFT ARROW (Move the insertion point to the beginning of the previous word)
CTRL+DOWN ARROW (Move the insertion point to the beginning of the next paragraph)

CTRL+UP ARROW (Move the insertion point to the beginning of the previous paragraph)

CTRL+SHIFT with any of the arrow keys (Highlight a block of text)

SHIFT with any of the arrow keys (Select more than one item in a window or on the desktop, or select text in a document)

CTRL+A (Select all) F3 key (Search for a file or a folder)

ALT+ENTER (View the properties for the selected item)

ALT+F4 (Close the active item, or quit the active program)

ALT+ENTER (Display the properties of the selected object)

ALT+SPACEBAR (Open the shortcut menu for the active window)

CTRL+F4 (Close the active document in programs that enable you to have multiple documents open simultaneously)

ALT+TAB (Switch between the open items)

ALT+ESC (Cycle through items in the order that they had been opened)

F6 key (Cycle through the screen elements in a window or on the desktop)

F4 key (Display the Address bar list in My Computer or Windows Explorer)

SHIFT+F10 (Display the shortcut menu for the selected item)

ALT+SPACEBAR (Display the System menu for the active window)

CTRL+ESC (Display the Start menu)

ALT+Underlined letter in a menu name (Display the corresponding menu)

Underlined letter in a command name on an open menu (Perform the corresponding command)

F10 key (Activate the menu bar in the active program)

RIGHT ARROW (Open the next menu to the right, or open a submenu)

LEFT ARROW (Open the next menu to the left, or close a submenu)

F5 key (Update the active window)

BACKSPACE (View the folder one level up in My Computer or Windows Explorer)

ESC (Cancel the current task)

SHIFT when you insert a CD-ROM into the CD-ROM drive (Prevent the CD-ROM from automatically playing)

Dialog Box Keyboard Shortcuts:

If you press SHIFT+F8 in extended selection list boxes, you enable extended selection mode. In this mode, you can use an arrow key to move a cursor without changing the selection. You can press CTRL+SPACEBAR or SHIFT+SPACEBAR to adjust the selection. To cancel extended selection mode, press SHIFT+F8 again. Extended selection mode cancels itself when you move the focus to another control.

CTRL+TAB (Move forward through the tabs)

CTRL+SHIFT+TAB (Move backward through the tabs)

TAB (Move forward through the options)

SHIFT+TAB (Move backward through the options)

ALT+Underlined letter (Perform the corresponding command or select the corresponding option)

ENTER (Perform the command for the active option or button)

SPACEBAR (Select or clear the check box if the active option is a check box)

Arrow keys (Select a button if the active option is a group of option buttons)

F1 key (Display Help)

F4 key (Display the items in the active list)

BACKSPACE (Open a folder one level up if a folder is selected in the Save As or Open dialog box)

Windows Explorer Keyboard Shortcuts:
END (Display the bottom of the active window)

HOME (Display the top of the active window)

NUM LOCK+Asterisk sign (*) (Display all of the subfolders that are under the selected folder)

NUM LOCK+Plus sign (+) (Display the contents of the selected folder)

NUM LOCK+Minus sign (-) (Collapse the selected folder)

LEFT ARROW (Collapse the current selection if it is expanded, or select the parent folder)

RIGHT ARROW (Display the current selection if it is collapsed, or select the first subfolder)

Windows Logo +U (Open Utility Manager)

Remote Desktop Connection Navigation:

CTRL+ALT+END (Open the Microsoft Windows NT Security dialog box)
ALT+PAGE UP (Switch between programs from left to right)
ALT+PAGE DOWN (Switch between programs from right to left)
ALT+INSERT (Cycle through the programs in most recently used order)
ALT+HOME (Display the Start menu)
CTRL+ALT+BREAK (Switch the client computer between a window and a full screen)
ALT+DELETE (Display the Windows menu)
CTRL+ALT+Minus sign (-) (Place a snapshot of the entire client window area on the Terminal server clipboard and provide the same functionality as pressing ALT+PRINT SCREEN on a local computer.)
CTRL+ALT+Plus sign (+) (Place a snapshot of the active window in the client on the Terminal server clipboard and provide the same functionality as pressing PRINT SCREEN on a local computer.)
((\(\o/)/))

Greeting

Smile/Laugh

Love/Flirt

Wink/Play

Mad, Mean, Angry, Sad

Innocent
]]> http://sightmap.wordpress.com/2008/08/20/funchoo-emotes/feed/ 0 DarkLight http://sightmap.wordpress.com/2008/08/20/scrabulous-2-word-list/ http://sightmap.wordpress.com/2008/08/20/scrabulous-2-word-list/#comments Wed, 20 Aug 2008 18:08:38 +0000 DarkLight http://omnifusion.wordpress.com/?p=593 ]]>

1. Google Labs : http://www.google.com/intl/en/options/
2. Add dictionary etc
3. Look for bud earphones for kat

WordPress
- DragonFaerie
- Omnifusion
- DarkLight Studio
- AlienTrance
- LoveDrum
- SightMap

Cannoli At Mike’s Pastry!

Penny’s Noodle Shop

950 W Diversey Pkwy  - Btwn N Wilton & N Sheffield Ave
Chicago, IL 60614 773 281-8448

[[GET MENU]]

• Laser Surgery
• More Memory For Laptop
• Hang Drum
• Swimming Pool

1. Sugar (Rice Pudding)
2. Milk
3. Flour
4. Salt
5. Chocolate Milk

Non-Grocery Essentials

1. Tupperware
2. Batteries (C, 9v?)
3. Etc.

It’s About Time…

1. Tubes !
2. Screens !
3. Bongo !
4. Laptop Mouse

javascript:document.body.contentEditable='true'; document.designMode='on'; void 0

Press [Enter] and you can now edit that page (Locally)

Chili Mac’s

Chilluminati
Yooo.  Best events ever.

Radiohiro
Radiohiro Army – WorldTrance

Shai
Divine Balance – PsyTrance DJ/Producer

Psymbolic
Psymbolic’s intentions are to break down the walls of collaboration inside and outside of art. Combine elements of art to create provoking environments. Continually grow, reach out and take new avenues. Share and provide individuals with inlets and outlets of creativity.

AudioGnomes

Angelynx Tarot – John Sacelli

Brilliantly Mad – Dave Zim

Pyrotechniq

Spunn

Touch Samadhi

DaddyCanDo

http://www.dadcando.com/

Travian: Tediously slow getting started, but very rewarding multiplayer civilization/strategy simulation.
Travian > Travian – Server 1

The Continuum: Very well put-together turn based strategy game, which is flash based and runs very smoothly.
The Continuum > Login – Launch Game

Monster’s Den: A Great little single-player RPG (Don’t delete your cookies though, or you lose your saved game like me!)
Monster’s Den

Kongregate: One of the best free online game portals I’ve found.
Kongregate > Kongai

Dragon Eggs

step 1Make a hole in either end of the egg

First of course you have to buy your egg (or raid the fridge). I used large hen’s eggs for this project (keeping it easy), but you could use duck, goose or even ostrich if you are feeling really adventurous. The beauty of the hen’s egg is that the glue gun hotmelt really works at this scale. If you go up in size, then you have to be prepared to do a lot more work to get the egg to look right.

Please use free range if you can… help chickens have a better life. Don’t worry about the waste, There doesn’t have to be any. Once you have blown the eggs, you can always make scramble or an omelet from the contents of the egg.

So, first off, wash the egg quickly in cold, slightly soapy water. In a minute you are going to be putting your lips to that egg surface and you know the last place that egg was !!

Now, to making the hole; strangely, this is not as easy as it sounds. For those of you with Dremmels, or miniature drills, (or dentists even) then this should present no problem, but for mere mortals, the egg is surprisingly hard, and being… well, an egg shell, is also quite brittle.

To make the hole you get a very sharp craft knife. Put the point of the tip of the blade against the tip of the egg at one end and turn back and forth about 180 degrees each turn. You’ll find it seems to take ages to get started. Don’t be tempted to push to hard or you will break the egg. If you feel that you are not getting started, then carefully scratch a cross at the end and put the tip of the blade at the centre of the cross and go back to turning it back and forth.

Once you break through the going gets easier, but you still have to take care as the blade can bite in and chip or crack the egg. If you are patient (only 5 minutes or so of turning) then within a few minutes you will have a hole about the size of a drinking straw. In fact you are aiming for a hole, the diameter of anything between a cocktail stick and drinking straw. Don’t worry if you do chip a little bit away, you will be covering that up with hotmelt in due course.

Make a hole like this IN BOTH ENDS.

image not found

560×325 : FHSQON1FBQ33VZX (0)

step 4Draw hot melt features on the egg

If you were making a regular painted egg, at this point, you would just start painting. However, this is Instructables and this is an Instructable on to make a Dragon’s Egg.

So, instead of painting the egg right away, draw some features on it with the hot melt glue gun. Of course you can do any pattern you like. In fact variety and invention is the key to making your dragon’s egg a real original. (As you can see one of the comments is that you could also make an Alien’s Egg, now how cool would that be… mmm might try that ).

But in case you want to practice before you branch out, here’s how I did it.

First: I drew loops round the upper half of the egg, while rotating it.

Second: I joined the tops of these loops to the top tip of the egg with more or less straight lines

Third: I joined the bottom of each of the loops to the bottom tip of the egg (right by the cocktail stick) with wavy lines.

image not found

450×500 : FYJVXSYFBQ33W18 (0)

step 6Distress the Dragon’s Egg

Now you should really distress your Dragon’s Egg a bit. After all Dragon’s Eggs have been known to be 1000′s of years old.

Like all distressing, all you have to do is paint a bit of grime on and wipe it off so that it goes in all the crevices, which of course you have just made using the glue gun.

Paint on black acrylic paint (or other contrasting colour) and then while it is still wet, wipe it off.

image not found

560×300 : FB8GKS4FBQ33W1S (0)

step 7Add surface highlights

This is an optional step. however, adding those last few details is great fun and does make the Dragon’s Egg look really special. I used gold rubbing paste (Rub n Buff (US), Gold Finger (UK)) but you could use a bit of contrasting paint on the finger tip or a luminous gel pen, for example.

image not found

out:{ top: 0.43364928909952605, left: 0.10178571428571428, width: 0.175, height: 0.14454976303317535, text:”add gold highlights using gold paint or gold faux gilding paste” }

add gold highlights using gold paint or gold faux gilding paste

KaptinScarlet

step 9Admire you Dragon’s Egg

To make a stand for it paint a bottle cap black, cut down a 35mm film tub (to about half an inch (1cm) should do it), or go to the dadcando egg stand project, and get the free downloadable template to make a really nice stand that has been specially designed for this egg.

Whilst you’re at it why not have a look at the Antique Mailing Box, which you can make to keep your Dragon’s Egg safe, and pretend that you got it from a far off land.

Whatever you do, have fun making this project. I think it will make the most original and exciting Easter gift for someone dear.

image not found

246×246 : FF75Z8AFBQ33W2T (0)

A few words about my propane (LP) tank HANK-DRUM
(“hank drum” — Hang + Tank)

I invented this instrument because of a love for the sound, music
and idea of the hang drum created by two dedicated artists at PANArt
company in Bern, Switzerland.

In lieu of not being able to procure such a hang drum from Switzerland,
I’m having a WHOLE lot of improvisational fun playing away on this simple
tank drum. As humble as the idea is, it plays very much like the real thing
& has a somewhat similar and quite pleasing sound. It is very responsive,
requiring only a light, one-fingered tap to start it singing nicely.

LATER NOTE: Many people have built hank drums from my plans here but of those I’ve
heard played (youtube and otherwise), over half of them are quite out-of-tune!!
I am at a loss as to why this is!! If you can tune a guitar, you can properly
tune this Drum. Please do not get impatient and settle for bad tuning –
for one thing, I am proud of my hank drum invention and it gives it a bad name
for people to be hearing (sometimes) way off tuning on the things! Take the
extra time to tune it right — it truly is NOT hard.

Another LATER NOTE: Nice to see a lot of home-made hank drums popping up on YouTube.
I do notice that quite a few folks are not hitting the tongues “properly”.
It makes a LOT (repeat LOT) of difference in the tone/sound/volume WHERE on the tongues
you hit. Try to hit the higher notes about a third of the way up from the base of the
tongues instead of at the end – EXPERIMENT. Lower notes aren’t as fussy. Also, a far
better tone is obtained if you hit quickly – not allowing your finger to rest on the
tongue even for an instant — tap it as if you were testing a stove burner to see if
it is hot. Also, I still see people not using the highly recommended bungee cords to
mellow out the tone. These may seem like small points, but they’re not.

CLICK HERE to see a short YouTube video of me playing this instrument
CLICK HERE to see a second video of me and this instrument

PS: The tiny, tinny speakers in most laptops do a very poor job of
representing the real sound of this instrument. Desk-tops do a far better job.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
PLEASE NOTE: A real, Swiss-made hang drum is VERY difficult to obtain
these days. A ray of hope is on the horizon however– Pantheon Steel,
a maker of beautiful steel drums (aka “steel pans”) is researching and
experimenting — with the intention of producing hang drums (under
a different name) for sale. Please contact them at pantheonsteel.com
and encourage them! They’re looking for signs of interest at this time.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

There is NO doubt that you can build this hank drum if:
a- You know how to use an electric drill
b- You know how to use a pipe wrench
c- You know how to use a saber-saw (only a few mins practice needed if you don’t)
d- You know how to use a pair of Vise-Grips
e- You know how to use a file
f- You can tune a guitar
g- You can get a friend to help you with a-f above
As you can see,basic stuff!

- IMPORTANT: USE ONLY NEW — NEVER-BEEN-FILLED — 20 pound propane tanks.
Input keywords such as – propane tank explosion – into YouTube to see
the reason why!! These new tanks cost $27 or so at Home Depot stores
(I’ve been told that they’re as low as $19 in big city discount outlets).
Even if you hear and feel no liquid in a used tank, there may still be
gas inside – which can be very explosive. Then too, valves have been known
to jam and the newer type LP valves can more easily fool one into believing
that a tank is empty. Heed this caution: use a NEW tank.

- Remove the valve mechanism using a monkey wrench. An “extender” is usually
needed to get the screw-threads to start turning (it’s glued-in/sealed
at the factory and take some determined convincing to unscrew). One fairly
sure-fire trick is to very tightly clamp a 2′ long hefty (1″ D.or so) length
of water-pipe vertically in a vise, then holding the tank on it’s side, slip
the handle-holes over the pipe. Now with the tank resting on the vise, use
the monkey-wrench/extender. This method works largely becasue it keeps the
tank stable — keeps it from rolling around. Be careful. An internal
float and valve mechanism is attached to the threaded top part & the
whole mess comes out as an attached unit – this can be discarded.

- The metal ring that is welded to the tank’s bottom also has to be removed.
It comes off quite easily with a sharp chisel. LATER NOTE (9/2/07): A far
easier and quicker way to remove this ring is to clamp Vise-Grip pliers
onto the ring, 1/4 inch from the ring/tank weld then worry it back & forth
a few times til it breaks free. Repeat with the other 3 welds. I just
de-ringed a tank this way in less than a minute. The welds usually break off
flush with the tank, but if not simply file off any leftover bumps. This
ring can be cut, re-formed and bolted onto the tank’s carrying-handle ring
(creating a complete circle) — this makes an excellent base that keeps the
tank from tipping over when set bottom-side up for playing.

- I use a regular off-the-shelf saber-saw to cut the tongues. The saw-blade
has to be ground-down so the back-side is half as wide, in order to follow
the curves of the tongues. WEAR SAFETY GOGGLES — the less-wide blade can
break all the easier with possibly disasterous results to eyes. I use
hearing protection too — look like a Martian! I prefer cheaper saber saws.
They’re lighter, easier to use and usually do NOT have this silly “no-screw”
spring-loaded blade “quick” attachment (which I find works very poorly). I
just bought a nice Black and Decker for $20. Also, small, cheap grinding
wheels, that are used with a regular electric drill, work nicely to grind
down the saw-blade. Home Depot and Walmart sell these wheels inexpensively.

- I always cut the tongue lengths a good 1/4 inch shorter than I think will
produce the desired note. After saber-sawing, the tongues are fine-tuned
using a bare hack-saw blade with the end wrapped in duct tape to keep from
cutting my hand. GO VERY SLOWLY — it’s FAR easier to flatten a note than
to sharpen it (to sharpen it, you have to run the saber-saw blade along the
perimeter of the tongue, seeking to nibble away a fraction of metal & reduce
the mass of the tongue – & thus raise the pitch — this process goes very
slowly in comparison with how lightning-fast the tongues can be flattened).

- The scale I used is D minor Pentatonic: (I fell in love with this scale after
hearing a fellow in Pennsylvania’s beautiful youtube uploads in this scale).
(low to high) Low note (“ding”) is D. Circle-notes are (running up the scale
& alternating right-left-right-left etc) A, C, D, F, G, A, C . You can make this
drum in any key/scale you’d like. Just use my template dimensions as a starting
point. For example, if you’d like to include an E note, refer to my F note and
just (carefully & slowly) lengthen each leg of the tongue until the E note is
achieved.

- The fact that the Low D note is NOT in the center, but instead is located
between the two highest notes, does not seem to be much of a liability. It IS
however, the closest note to the center. I’d LIKE to have put it in the center,
but after doing so on an experimental tank, it confounded the other notes
considerably — thus this “off-center” placement. I’m sure hang players would
have little trouble playing this slightly off-center Low D “ding”.

- The saber-sawing process magnetizes the filings to a point where they’re
quite pesky! While sawing and tuning, I find that taking an old towel and
forcefully whapping each tongue dislodges these filings nicely. Once all cut
and tuned, I insert a garden hose under high pressure into the tank and let
it run for about ten minutes while rotating and swishing around the tank.
This gets rid of the metal filings.

- Tuning the beast:
I rough-tune each tongue by ear to just a bit higher-pitch than desired,
then use a simple electronic tuner to fine tune each tongue to pitch.
Here are a few tricks I have found to be quite useful in the process.
I start with the low A tongue, silencing all the other tongues by
sticking a pea-sized glob of “Mortite” brand window-caulking “rope”
(actually very clay-like), available at any hardware store, across the
top of the roundy end of each tongue. Thus silenced, the overtones
and harmonics of these notes don’t confound the electronic tuner.
For reasons I don’t understand, (stringed and wind music generation I DO
understand — but the best I can do with this musical-steel stuff is to
take my best guess, then launch into a barrage of adjustments & experimentation
until I find something that works to my liking. There are lots and lots of
variables with musical-steel methinks!!) the two highest notes tune (& sound)
noticeably better with NO Mortite silencing the other notes. For fine-tuning,
lengthening of the tongues, I only use a hacksaw blade itself. An observation:
Please take the time and care to tune this thing properly. Quite a few folks
have built one of these hank drums & several have sent me sound samples while
others have uploaded to YouTube. While many of these sound quite nice, in far
too many cases, it’s obvious that their tongues are not tuned properly — one
or more note(s) being out of pitch! It’s not that hard at all to get it right –
CLOSELY follow my tuning instructions (do not “wing it”), go slow and you won’t
go wrong.

- A bungee-cord or two (or even three) wrapped around the tank just down from
the tongues really does do wonders in helping control any excessive tank ring as
well as undesirable overtones. I can’t imagine playing one of these instruments
with no bungees. LATER NOTE (8/23/07): Just discovered that black rubber bungees
work FAR better than round, multi-color, cloth-covered ones — must be due to more
contact area. Here again, videos sent me and on YouTube show people playing these
drums without bungees — far too ringy & brash a sound!

- Later note: I just had occasion to play this drum with the thing’s base resting
on concrete & was amazed to hear just how much the sound suffered – lower notes
were muffled. I’d only played it on carpet, grass or in my lap previously.
Must be that the sound conducts into the concrete & acts similarily to a mute
on a fiddle. This problem was completely solved by taking a short length of
discarded garden-hose, splitting it lengthwise & working it onto the base,
securing it a few times with colored duct-tape. Also has the advantage of not
scratching any surface that the drum rests on.

An alternate method of expanding the above digitalized template to proper
size is to use the old “grid-square” method. I have applied grid squares
to the template — each square on the template represents a quarter of an
inch — even though it obviously does not measure 1/4″ on the computerized
template. Carefully tape together several sheets of 1/4″ graph paper taking care
that where sheets overlaps, all lines line-up. Look carefully at a square on a
tongue — count where the corresponding square should be on the blank graph
paper & carefully draw in the tongue line. It’s not that critical so long as
when it comes time to actually cut the metal, you leave each leg of
the tongue amply long (at least a quarter inch) for fine-tuning. Crafters -
quilters, rug-weavers all use this simple “grid-square” method to expand small
magazine designs to whatever size they wish.

This instrument is not especially light — an off-the shelf tank weighs 17 pounds
(a pound or two less with the bottom ring and valve mechanism removed) but it does
have a comfortable built-in carrying handle. In my case, the weight has not been an
issue. I cart it around to all sorts of places quite easily.

LATER NOTE: While I’ve never been at all interested in any commercial venture with my
instruments, I nonetheless have obtained a number of new propane tanks recently with
the intention of offering some of my Hank creations for sale. I find the time necessary
to turn these tanks into hanks in very very short supply. What I can say is that if/when
some become available, the first thing I will do is to announce that fact on this
webpage and perhaps on my YouTube postings. Thanks for all those encouraging me in this
regard.

If more “would-be-hang-drum-players-who-can’t-obtain-a-PanArt-instrument” saw how
easy this thing is to make, how good it sounds in person & how much GREAT fun it is
to play, I think that they’d be more around.  But please TUNE the contraption properly!!

CLICK HERE to see Jim Doble’s neat-looking thick-metal, BIG-tank playground drums! Beautiful! Gotta try something that big with a Hank!! Dennis Havlena – W8MI dhavlena@gmail.com Mackinac Straits, northern Michigan Originally posted July 3, 2007